The 10 Most Terrifying Things About Repairs To Upvc Windows

Repairs to uPVC Windows

uPVC windows are an excellent choice for modern homes. They are easy to maintain, durable and long-lasting. Unlike timber and aluminium, they are not susceptible to corrosion or rot.

Cleaning and lubricating regularly UPVC windows and doors is crucial. This will save you from unnecessary repair costs and improve the efficiency of energy.

1. Broken Glass

The broken glass in your windows can cause severe damage to your home and even be fatal. It is important to ensure that your windows are in good condition.

For single pane windows, it is relatively easy to replace them, and the new window will generally fit within the frame that was previously installed easily. However when you have double pane windows that are held in place by internal beading it will be more difficult to remove the existing panes and install new ones. In this situation you'll need find some plastic spacers that help the new pane to fit properly into the frame of the window.

If you're planning to try to remove the window panes by yourself it is crucial to wear appropriate safety gear, including thick gloves and protective eyewear. It is also recommended to lay down a drop cloth before you begin working on the window panes, so that any shards fall onto the fabric and not on the floor which could cause them to be trampled under.

Once the glass has been removed from the window, it's best to seal the gap with clear packaging tape or duct tape to stop water and drafts from entering the home until a professional is able to come out and repair the window. This will also provide a barrier to prevent any intruders from making their way into your home. If the gap between the door and the window is substantial, you may need to consider an alarm system that has an opening. This will provide the best of both.

2. Sagging

Upvc is a long-lasting and energy efficient alternative to timber sash windows. Over time, they can develop a variety of issues, including sliding. A window that is sagging can cause problems with light, draughts, and even security. It's crucial to act as soon as you discover that your uPVC windows are falling down.

Repositioning the hinges could aid in fixing a window which is sagging. To accomplish this, you'll need to open the window to get to the frame. Then, remove both the hinges on the top and bottom using a screwdriver, and then adjust them counter-clockwise or clockwise. Close your window to check the fit after you've repositioned your hinges. If you're happy with the fit, tighten the screws to ensure that they remain in position.

If you are unable to reposition the hinges, you might have to replace the seal. Rubber seals may dry out and lose their elasticity with time, which causes them to loose their elasticity. It is essential to replace your seal as soon as you can to ensure that your uPVC window watertight and draughtproof.

uPVC handles may also become loose. The majority of the time it is due to screws that have become loose over time. However, it could be due to the fact that the handle mechanism has been worn out. Fortunately, it's easy to fix the handle of a window that is loose yourself. First, you'll need to shut the window and then perform an initial fitting. The joint at the corners of the sash should align with the joint on the casing. If it doesn't, you can make use of a screwdriver to loosen the handle, and then turn the mechanism back into position.

3. Water Leaks

If you awake to wet floors and mouldy walls each time it rains it's important to take action. The leaks of water through windows could cause structural damage to your home and also hinder your ability to control the temperature of your home. The most common reason for leaks in uPVC windows is that the sealant around the frame is either damaged or is missing.

This is an easy fix that can be accomplished by anyone who is a DIYer with the skills. Depending on the severity of the issue is, the old caulking may need to be removed. When it comes to uPVC repair, you must be careful not to over-caulk. This will make your window harder to clean and lower its energy efficiency.

Verify that the drainage holes do not have debris inside them and that the sill pan has been properly angled to drain away from the window. In more serious cases you might need to consider replacing the window.

Moldy sills and rotten ones are also signs of water leakage. The fungus thrives in damp conditions and can spread quickly throughout the home.

If the leakage occurs between the double-glazed window, it is more likely the issue is with the seal rather than the frame. A upvc window repairs near me specialist can fix this issue by replacing the glass seal. This will restore the full insulation of your windows.

4. Faulty Hinges

If your uPVC windows are difficult to open, or slack and blow open with a breeze It could be hinges at fault. They can be easily replaced by any competent DIYer and are usually completed in just a few minutes.

Like any mechanical component hinges are prone to wear out over time. Changing a window hinge is an easy procedure, but it is simpler with someone else to help you hold the frame up.

Make sure that the uPVC hinges are closed and open in the correct direction. This can be done by checking for the arrows on each hinge, this shows which way the window should open.

Window hinges that aren't working properly can be caused by incorrectly opening the window in a certain manner or because of poor installation at the factory. Sending us a photo via our website will often resolve the problem. We are happy to offer suggestions.

It is also crucial to ensure that the hinges are lubricated regularly. Applying an engineering lubricant that is light to the hinges is an ideal way to do this. We suggest using a lubricant that does not contain solvents, such as 3-in-1 Multi-Purpose oil. Regular lubrication will make the window easier to open and close. It can also reduce the chance of windows sticking and prevent corrosion. This is recommended to be done at least every year. WD40 and other solvent based lubricants are not recommended as they can damage the parts of your uPVC window.

5. Draughts

Draughts can be caused by different causes. The hinges, also due to wear and tear can become misaligned, this will cause a gap to form where the sash joins the frame. This can be easily repaired by giving them thorough clean, however if they are beyond repair it could be necessary to have them realigned or replaced. The interlock may also become disaligned. It is located on the hinge's side, and could require to be cleaned. In some cases it might be necessary to replace them.

The next most common reason for draughts are the window seals. They are prone to wear or upvc damaged over time and will allow air to escape through the gaps. Installing high-quality weatherstripping is a good way to keep draughts at bay. Replace the windows made of Upvc with low-emissivity glass. This will help control indoor temperatures, and reduce the risk of draughts.

Another method of reducing the amount of draughts is to use a Draught-excluder. These are usually made of fabric tubes filled with a filler which can be placed over your window sill. They can help block out cold air and keep your home warm and cosy!

With a little maintenance and repairs your windows made of upvc will provide excellent security and insulation for your home. It is crucial to keep in mind that all windows eventually get worn out and it could be cheaper to replace them instead of fixing them. So, if you are experiencing issues with your Upvc windows, it's recommended to seek help from a professional as soon as possible.