11 Ways To Totally Block Your Repairs To Upvc Windows

Repairs to uPVC Windows

uPVC is a great option for modern homes. They are easy to maintain, durable and long-lasting. Unlike timber and aluminium, they don't get rusty or decay.

It is important to clean and oil UPVC doors and windows on a regular basis. This will save you from unnecessary repair costs and also improve the efficiency of energy.

1. Broken Glass

The damaged glass in your windows could cause significant damage to your home, and could even be fatal. It is crucial to take the time to make sure that you are doing everything you can to keep your windows in good repair.

Single-pane windows are fairly simple to replace, and they generally fit into old frames very easily. If you have double glazing repairs-paned windows which are joined by internal beading, it will be harder to remove and replace the old panes. In this situation, it is necessary to buy plastic spacers to help the new pane fit into the window frame.

Wearing eye protection and thick gloves is essential when you are planning to remove the glass yourself. You should also lay down a dropcloth prior to you begin working on the window panes to ensure that any shards fall onto the fabric, not onto the floor, where they could be trampled under.

It's a great idea to cover the gap with tape after the glass is removed. This will keep drafts and water from getting into your property until a professional comes out to fix the window. It also acts as a barrier, deterring any intruders to gain access to your home. If the gap is large, you might think about the security door with an integrated window, since this will offer the best of both worlds.

2. Sagging

uPVC is a durable, energy-efficient and affordable alternative to timber sash windows. Over time, Window Repair they can be affected by a variety of issues, including sagging. A sagging uPVC window can cause problems with light, draughts and even security. It's crucial to act as soon as you realize that your uPVC windows are falling down.

To repair a window that is sagging, you can try to reposition the hinges. You'll first need to open the windows so you can reach the frame. Then, using an screwdriver, remove the top and bottom hinges and adjust them by turning them clockwise or counter-clockwise. Close your window to check the fit after having repositioned your hinges. If you're satisfied with the fit, tighten the screws to ensure that they stay in position.

If you cannot reposition the hinges, you might need to replace the seal. Over time rubber seals can lose their elasticity and dry out which causes them to lose tightness. If this happens, it's essential to replace the seal as quickly as possible so that your uPVC windows are watertight and safe from drafts.

uPVC handles may also become loose. This is often caused by screws that have been removed over time, but it could be due to the mechanism of the handle wears out. It's relatively simple to repair a loose uPVC handle. First, you'll need to close your window and do an experiment fit. The joints at the corners of the sash should be aligned with the joint on the casing. If it isn't you can use a screwdriver to loosen the handle. Then turn the mechanism to position.

3. Water Leaks

If you awake to wet floors and damp walls every time it rains it is important that you take action. The leaks of water through windows could cause structural damage to your home, and affect your ability to regulate the temperature of your home. The most common cause for leaks in uPVC windows is that the sealant around the frame is damaged or is missing.

It is a fairly easy fix that can be done by any skilled DIYer. Based on the severity of the issue the old caulking may need to be removed before a fresh layer can be applied. When it is time to uPVC repair, it is important to avoid over-caulking. This will only make your window harder to clean and reduce its energy efficiency.

Make sure that the drainage holes are free of debris in them and ensure that the sill pan is angled correctly to drain away from the window. In more serious cases you might have to consider replacing the window.

Moldy sills and rotten ones are other signs of water leakage. This mold thrives in damp environments and is able to quickly spread throughout the house.

It is also important to note that if the leak originates from the glass of your double-glazed windows, it is more likely to be an issue with the glass seal, rather than the frame or sagging. Again this can easily be repaired by an uPVC window specialist who will replace the glass seal and restore the full insulation properties of your windows.

4. Faulty Hinges

Hinges could be at fault when your uPVC window is difficult to open or it blows open with the breeze. They can be easily replaced by any competent DIYer and are usually completed in just a few minutes.

Like all mechanical parts, hinges can wear out over time. It is essentially a very simple process, but it's easier to do if you have someone to help you hold the frame in place.

Verify that the uPVC hinges are open and closed in the right direction. You can do this by looking for the arrow on each hinge. This indicates which way the window should be opened.

The issue can be caused due to opening the window in the wrong way or due to a poor installation in the factory. This can often be resolved by sending us a photograph on our website. We will be happy to give you advice.

It is also essential to lubricate the hinges on a regular basis. This can be accomplished by applying a light engineering oil to the hinges. We recommend using a solvent-free lubricant, such as the 3-in-one Multi-Purpose oil. Regular lubrication will make the window easier to open and close. It also helps prevent corrosion and reduce the possibility of sticking. This should be done at least once a year. WD40 or other solvent-based oils are not recommended as they could damage your uPVC windows.

5. Draughts

Draughts can be caused by several different things. The hinges, also because of wear and tear, may become displaced, which will cause an opening to appear where the sash meets the frame. They can be repaired by giving them good clean, but if they are beyond repair it might be necessary to get them re-aligned or replaced. Second, the interlock can also become disaligned. This is located on the hinge's side and may need to be cleaned. In certain instances it might be necessary to replace these.

The next common reason for draughts are the Window Repair seals. They are susceptible to being worn out or damaged over time, and allow air to escape through these gaps. This can be avoided by replacing them with high-quality weatherstripping. Another option is to replace the upvc window with low-emissivity glass. this will help in regulating indoor temperatures and will lessen draughts.

The last way to reduce draughts effectively is by using a draught-excluder. These are usually fabric tubes filled with a filler, which can be hung over your window sill. These will keep your home warm by blocking out cold air.

The windows made of upvc can remain a great source of insulation and security in your home with a little regular maintenance and repairs. It is crucial to recognise that windows last for a certain period of time and there may come the point when it's more economical to replace them than repair them. So, if you're experiencing problems with your upvc windows, it is recommended to seek help from a professional as soon as you can.