17 Reasons You Shouldn t Beware Of Repairs To Upvc Windows

Repairs to uPVC Windows

uPVC is a great choice for modern homes. They are easy to maintain and durable, as well as long-lasting. They do not rot or rust like timber and aluminum.

It is essential to clean and oil UPVC doors and windows regularly. This will reduce repair costs and increase energy efficiency.

1. Broken Glass

The broken glass in your windows can cause severe damage to your home, and could even be fatal. It is essential to take the time to ensure that you're doing everything you can to keep your windows in good condition.

For single pane windows it is relatively easy to replace windows, and the new one is usually able to fit into the frame that was previously installed easily. If you have double-paned windows that are held together by internal beading, it will be harder to remove and replace the old panes. In this instance it is essential to buy plastic spacers to make sure that the new pane fits into the window frame.

Wearing eye protection and thick gloves is essential for anyone who plans to remove the glass yourself. It is also recommended to lay down a drop cloth before you start working on the glass to ensure that any fragments of glass fall onto the cloth instead of onto the floor, where they could be trampled upon and cause further damage.

It's a good idea to tape the gap once the glass is removed. This will stop drafts and water from entering your property until a professional arrives to repair the window. It also acts as a barrier, preventing any intruders to gain access to your home. If the gap is particularly large, you might think about an alarm door that comes with an integrated window, as it offers the best of both worlds.

2. Sagging

uPVC is a durable energy-efficient, cost-effective and economical alternative to timber sash window. However, over time, they may be afflicted by a variety of problems including sliding. A window that isn't properly aligned can cause problems with light, draughts and even security. If you notice that your uPVC window is beginning to lose its shape, it's important to act quickly to prevent the problem from becoming worse.

To repair a window that is sagging, you can try to reposition the hinges. To accomplish this, you'll have to open the window so that you can get to the frame. Then, you can remove the hinges on the top and bottom with a screwdriver and adjust the hinges clockwise or counter-clockwise. After you've repositioned the hinges, close the window and verify the fit. If you're satisfied with the fit, tighten the screws until they stay in the right place.

If you are unable to move the hinges, you may need to replace the seal. As time passes, rubber seals lose their elasticity and become dry, which causes them to lose tightness. It is important to replace your seal as soon as you can in order to ensure that your uPVC window repair waterproof and draughtproof.

UPVC handles can also become loose. The majority of the time, this is caused by screws that have become loose over time. However, it can be due to the fact that the handle mechanism has been worn out. It's relatively easy to repair a loose uPVC handle. First, you'll need close your window and do an initial test fit. The corner joints of the sash should align with the casing joint. If it doesn't then you can make use of a screwdriver to loosen the handle and then reverse the mechanism back into position.

3. Water Leaks

If you wake up to damp floors and mouldy walls every time it rains it's important to take action. Windows that leak water do not only lead to the degradation of your home's structure but also undermine your efforts to regulate the temperature in your home. The most frequent reason for leaks in uPVC windows is that the sealant surrounding the frame is either damaged or is missing.

It is a fairly easy fix and should be undertaken by any skilled DIYer. Depending on the severity of the issue is, the old caulking might need to be removed. It is crucial to keep in mind that when it is about uPVC window repairs, you should not be tempted to 'over-caulk in order to make the area more difficult to clean and Window Repair can reduce your energy efficiency.

Check that any drainage holes are free of debris inside them and ensure that the sill pan is properly angled to drain away from the window. In more extreme situations, you may have to replace the window.

Moldy sills and rotten ones are another sign of water leakage. This fungus thrives in humid conditions and can propagate quickly throughout the home.

If the leakage occurs between the double-glazed glass it is more likely that the issue is more with the seal than the frame. This can be easily corrected by a uPVC window expert who can replace the glass seal and regain the full insulation properties of your windows.

4. Faulty Hinges

If your uPVC windows are stiff to open, or loose and blow open in a breeze it could be the hinges that are at fault. Anyone who is a skilled DIYer can fix these in a matter of minutes.

Like any mechanical part, hinges can wear out over time. The process of replacing a hinge on a window is essentially a simple procedure, but it is simpler with someone else to assist in holding the frame up.

Make sure that the uPVC hinges are closed and open in the right direction. Look for the arrows that are on each hinge to determine which way the window should be opened.

The issue could be caused due to opening the window in the wrong way or by a poor installation at the factory. This issue can be fixed by sending us a photo through our website and we will be pleased to offer you suggestions.

Regularly lubricating the hinges is essential. This can be done by applying an oil that is light in nature to the hinges, we recommend using a solvent-free lubricant such as 3-in-one Multi-Purpose Oil. Regularly lubrication makes the window easier to open and close. It can also stop corrosion and decrease the chance of sticking. It is recommended to do this once a year. WD40 and other solvent-based lubricants should not be used as they could damage your uPVC windows.

5. Draughts

Draughts in windows made of upvc can be caused by a variety of different things. The hinges can also become unbalanced due to wear, creating an opening where the sash and frame meet. If they are damaged beyond repair, it might be required to realign them. Second, the interlock can also become unbalanced. This is located on the hinge's side, and could require to be cleaned. In some cases it is possible to replace them.

The second most frequent reason for draughts is Window repair seals, these can become worn down or damaged over time and allow air to escape through these gaps. This can be prevented by replacing them with high-quality weatherstripping. Another option is to replace the window with low-emissivity glass. this will help to regulate indoor temperatures, and also lessen the risk of draughts.

The last way to reduce drafts effectively is to use a draught-excluder. These are typically fabric tubes filled with a filler that can be put on top of your window sill. They can help keep cold air out and keep your home warm and cosy!

With a bit of regular maintenance and repair, your upvc windows will provide excellent security and insulation for your home. It is crucial to keep in mind that all windows will eventually become worn out, and it is more cost-effective to simply replace them than to repair them. So, if you're experiencing issues with your Upvc windows, it's best to seek professional assistance as soon as possible.