Don t Buy Into These "Trends" About Fiat Panda Key Fob Replacement

Reasons Your Fiat 500 Key Fob Won't Work

A fiat punto key fob replacement 500 key fob makes it simple to open doors and start your vehicle. There are a myriad of reasons why the key fob might stop functioning. This could be due to a dead battery and water damage, as well as problems with receiver modules, as well as interference.

This listing is for a NEW replacement Fiat Flip Key Remote - like the Ilco brand that must be professionally programmed by a local automotive locksmith (click here for Locksmith Search). Includes lock, unlock and trunk buttons.

Dead Coin Battery

A dead battery is the main cause of your 500 key fob not working. Modern key fobs have a very limited operating range and must be within some feet of the vehicle to operate. If you're far away from your vehicle and you press the key fob button the car won't be able to respond, and will display a "Key Fob Not Detected" message in the instrument cluster.

If this happens, replace the battery on your coin cell (Part number CR2032) with a new one from a reputable brand such as Panasonic, Duracell, or Energizer. You can find them in your local hardware store or online.

After you've replaced the battery in the coin cell you can test it by standing close to your Fiat 500 and pressing the buttons. The parking lights should flash and the key fob should operate the lock and unlock switches.

If your key fob isn't working even after replacing the battery, there might be water damage that has prevented it from communicating with the module in your vehicle. Water damage can happen in a variety of ways, such as the simple splash or submerging the key fob into saltwater at the beach. If you think your fob was exposed to water, place it in a bag of rice to draw out the moisture. If that doesn't work, your fob will probably need to be reprogrammed by an experienced auto locksmith or by the dealer.

Water Damage

Water damage can occur if you immerse the fob in the ocean or wash it in a washing machine. Saltwater can cause the circuit board to short, and eventually cease to function. It's not a good thing to get the fob wet however, don't give it up when you accidentally drop it in water or forget to remove it from your pants pocket.

First take the battery off the fob. Clean the electronic chip using isopropyl alcohol or a similar product and dry it completely before replacing the battery. Then test the fob to test if it works. If the fob doesn't function, it may need to be changed. This is usually handled by an auto locksmith or dealer.

If the key is a newer model and has never been programmed to your car it is likely to need to be replaced completely. This is an easy process that can be handled by a professional locksmith for automotive use. The locksmith will need the key cut to match your vehicle's ignition. The locksmith will also have to reprogram the fob into the vehicle's system. This is a fast and cost-effective process that is usually completed in the same day.

Receiver Module Issues

One of the most common reasons your 500 key fob may stop functioning is because it's out of range. The remote's range is of 30 feet. Therefore, should you be too far away from your vehicle it won't respond to your commands. You can easily solve this problem by moving the remote closer to your vehicle until it responds.

If you've replaced your coin battery (commonly known as"button" or "button" or "watch") and the fob won't work It could be because of an internal circuit board problem. In the majority of cases, reprogramming your fob will solve the problem. There are instructions on how to do this on the majority of automobiles by searching YouTube or reading the owner's manual.

It's possible that you need to replace the metal retaining clips that keep the coin battery. If they loose tension it could hinder the coin battery from being seated properly and cause the remote to malfunction.

In rare instances, the fob can become out of connection with your vehicle as a result of hardware or software problems. This issue can be fixed by visiting your local dealer or auto-locksmith to reprogram your key fob. In some cases the software may require reinstallation in your body control modules.

Interference

Interference can also cause the key fob to not be able to receive or transmit signals. This could happen if the key fob is close to a radio transmitter (cell phones and radar detectors) or any other source of electromagnetic radiation. The key fob may not function because of a problem to the buttons water damage or [empty] damage to the internal chips.

If the key fob has suddenly stopped working, in the middle of the night, or after trying every option at home to solve it e.g. It could be a defective 500 receiver module in the event that you've tried replacing the battery, reprogramming it, or using an alternative key fob. The receiver module is located under the dash and picks up the radio frequency signals from the key fob. It transforms the signals into electronic commands that are then translated by the vehicle.

Fortunately, there's an easy way to reset every single system on board in your 500, including the key fob. Disconnect the 12 volt battery for about 15 minutes, transponder by taking off the negative cable first then the positive cable. Reconnect the battery. This will remove any remaining electricity and restart the car's computers. This could help the key fob to function again. If the issue continues you should speak with an expert certified technician. They will be able to determine the root of your problem.