The 10 Scariest Things About Repairs To Upvc Windows

Repairs to uPVC Windows

uPVC windows are a great option for modern homes. They are long-lasting, durable and easy to maintain. In contrast to aluminium and timber, they are not susceptible to rust or rot.

It is essential to clean and oil UPVC windows and doors on a regular basis. This will help prevent costly repairs and improve the efficiency of energy.

1. Broken Glass

The damaged glass in your windows could cause severe damage to your home and even be fatal. It is essential to make sure that your windows are in good shape.

For single pane windows it is relatively easy to replace them, and the new window is usually able to fit into the frame that was previously installed easily. However when you have double pane windows that are secured by internal beading, it'll be more difficult to get rid of the panes that are in place and replace them with new ones. In this instance you'll need to locate some plastic spacers to assist the new pane to fit correctly into the frame of the window.

If you're planning to try to remove the window panes yourself it is crucial to wear the proper safety gear that includes gloves with a thick layer of material and eye protection. It is also recommended to lay down a dropcloth prior to you begin working on the window panes to ensure that any shards fall on the fabric and not onto the floor which could cause them to be trampled under.

After the glass has been removed and the glass is removed, it's a good idea to seal the gap with packaging tape or duct tape to block water and drafts from getting into the home until a professional can come out and repair the window. It also acts as a barrier that will prevent any intruders from getting access to your home. If the distance between the door and the window is large, you might want to use a security screen that also includes windows. This will give you the best of both.

2. Sagging

uPVC windows and doors are a low-cost energy-efficient, durable and long-lasting alternative to timber windows made of sash. As time passes, they may develop a variety of issues such as sliding. A sagging window can cause problems with light, draughts or even security. If you notice that your uPVC window is beginning to sag it's crucial to act fast to prevent the problem from becoming worse.

To repair a window that is sagging, you can try repositioning the hinges. First, you'll need to open the windows so you can get at the frame. You can then unscrew both the top and bottom hinges with a screwdriver and adjust them clockwise or counter-clockwise. Once you've adjusted the hinges, shut your window and check for fit. If you're happy with the fit, you can tighten the screws until they remain in the right place.

If you are unable to move the hinges, you might need to replace the seal. Over time, rubber seals lose their elasticity and become dry which causes them to lose tightness. It is important to replace your seal as quickly as you can in order to keep your uPVC window waterproof and draughtproof.

uPVC handles can also become loose. This is often caused by screws that have become undone over time, but it could be caused by the handle mechanism wearing out. Luckily, it's not difficult to repair the handle of a window that is loose yourself. You'll first need to close the window and Window Repairs then perform a test fitting. The joint at the corner of the sash should be aligned with the joint on the casing. If it does not then you can use the screwdriver to loosen the handle. Then, you can turn the mechanism to position.

3. Water Leaks

If you're waking up to wet floors and mouldy walls every time it rains it's important to take action. The leaks of water from windows do are not just a cause for destruction of your home's structure but also undermine your efforts to regulate the temperature inside your home. The most common reason for leaking uPVC windows is that the sealant surrounding the frame has been damaged or missing.

This is a relatively easy fix that can be completed by any skilled DIYer. Depending on the severity of the issue the old caulking may require removal before a fresh layer is applied. It is essential to keep in mind that when it is about uPVC window repairs you should not be tempted to 'over-caulk and then make the area more difficult to clean and can decrease the efficiency of your energy usage.

Verify that the drainage holes have no debris inside them and that the sill pan is angled correctly to drain away from the window. In more serious cases you might need to consider replacing the window.

Other signs of long-term water leakage are rotted sills and the appearance of black spots of mold on the wall near the window. The fungus thrives in damp conditions and can spread quickly throughout the house.

If the leakage occurs between the double-glazed glass, it is more likely the problem is with the seal rather than the frame. A uPVC specialist can fix this problem by replacing the glass seal. This will restore the full insulation of your windows.

4. Faulty Hinges

If your uPVC windows are brittle to open, or slack and blow open with ease It could be hinges at the fault. These are easily repaired by any DIYer who is skilled and can usually be completed in just a few minutes.

Nearly every home in the UK will have top-hung or side-hung upvc window repairs near me windows that use hinges and, like all mechanical parts, they are susceptible to wear and tear over time. It's easy to change the hinges on a window however it is easier if someone else helps hold the frame.

It is also important to ensure that the uPVC hinges are being opened and closed in the correct direction. Look for the arrows that are on each hinge to determine the direction in which the window should be opened.

The problem can be caused by opening the window improperly or due to a poor installation at the factory. Sending us a photo via our website will often resolve the problem. We are more than happy to provide advice.

Regularly lubricating hinges is also essential. This can be done by applying an oil that is light in nature to the hinges. We recommend using a solvent-free lubricant, such as the 3-in-one Multi-Purpose oil. Regular lubrication can allow the window to operate and close more smoothly. It can also lower the risk of a window sticking and help prevent corrosion. It is recommended to perform this every year. WD40 and other solvent based fluids are not recommended since they can damage the parts of your uPVC window.

5. Draughts

Draughts in upvc windows can be caused by a few different factors. Firstly the hinges, again due to wear and tear can become misaligned, this will cause a gap to form where the sash meets the frame. If they're beyond repair, it may be necessary to get them re-aligned. The second is the interlock, which is located on the hinge of the window, can be misaligned. Again, it may be possible to just give them a clean but in certain cases, it may be necessary to have these replaced.

The seals may wear out or become damaged over time, allowing air escape. Replacing these with high-quality weatherstripping will help to keep draughts at bay. Replace the windows made of upvc with low-emissivity lenses. This will help to regulate indoor temperatures and decrease draughts.

One of the most effective methods to reduce drafts is to use a draught excluder, these are usually fabric tubes which are filled with a type of filler. They can be put on top of your windowsill. These will keep your home warm by blocking out cold air.

Your upvc windows can continue to provide excellent insulation and security to your home with a little regular maintenance and repairs. It is essential to remember that all windows will eventually get worn out and it may be more cost-effective to replace them than to repair them. If you have any problems with your Upvc window you should consult a professional as soon as you can.